Electric shavers can stop working efficiently for various reasons, but it is usually something that you can fix on your own without buying more parts and spending money.
A Braun shaver is a good-quality, trusted brand name for men's electric shavers. There are a couple tricks to try to see if you can get yours working again, or working more efficiently.
Charge the Braun shaver completely if it is electric. Sometimes, the battery pack may need to be replaced even if it is charged regularly, such as a cellular phone. Take it into a men's body shop store to see if they can change it for you. Replace the foil and cutter every 9 months to keep it sharp and unclogged. Sometimes the mechanisms in these parts can wear down, causing the Braun shaver to work more slowly and less efficiently. Check out the foil and cutter on the inside if the problem is not fixed yet.
Unplug the shaver. Depending on the type of Braun shaver it is, there will either be a pressure button or screw to take out to get inside the foil and cutter. Clean the screen with a small brush. Remove the blades and use air duster spray to clean them. Obtain shaver oil lubricant and lubricate all parts inside the foil and cutter. Sometimes, lubrication is the key to get the Braun shaver working well again. Clean the Braun shaver at least once a month thoroughly to help it have a long life.
If the problem still is not fixed, you may need to bring it to the manufacturer for bigger problems. By: Lauren Wise.If your Philips Shaver is not working or turning on, read below the possible causes and our advice on how to solve them yourself.
If you have a rechargeable Philips Shaver, it is possible, that its battery has run out. We advise you to charge your shaver and then try turning it on again. For details on how to charge your shaver, please refer to the user manual.
If your Philips Shaver is not rechargeable then it should be plugged into a working electric socket while in use. It is possible that your shaver does not turn on or move because it is dirty. There can be hair or dirt particles stuck inside it, causing the shaving heads to become blocked. To fix this problem, properly clean your shaver. If possible, remove the shaving head and clean your shaver from the inside as well. For detailed cleaning instructions, refer to your user manual.
In some shavers, a cleaning reminder symbol will blink to let you know that the shaver needs to be cleaned. Another reason why your shaver might not be working is that it is not assembled correctly. For full instructions on how to reassemble your shaver, refer to your user manual.
Some Philips Shavers have a 'travel lock' function. If this is activated, the shaver does not turn on. Depending on the shaver model you have, you may see a 'lock' symbol blinking on your shaver to let you know that the travel lock is activated. Now try turning the shaver on again. It is possible that your Philips Shaver is damaged to such an extent that the motor cannot run anymore. In this case, please contact us to see how we can further help.
Find your product. Not what you are looking for? Did we answer your question? If not, contact us. Chat Now Chat Now. Payment We accept the following payment methods:. Help with your online order. Frequently asked questions. Terms and conditions.
Search order. Student discount.Your electric shaver is your most prized grooming possession because it allows you to maintain your look each and every day, quickly and conveniently. A lot of guys will run out and buy a new one not knowing that they might have been able to fix their old one. In most cases, a shaver problem can be easily identified and resolved. It just takes a little patience and a few troubleshooting techniques.
You might also need to check the charge on a battery operated shaver if it is running but sluggishly. You may need to service it to make sure everything is clean.
There are foil head shavers and rotary head shavers. And, while they both do the same thing, they function just a little differently. Before servicing your electric shaver you must absolutely remove it from the power source.
Take the plug from the wall or remove the batteries before you begin. Next, remove the screen from the head and clean thoroughly. There might be dust or hair stuck in there that needs to be removed.
Finally, lubricate your shaver according to the instructions in your user manual from the manufacturer. The more you use it, the more the foil wears and it could develop holes that can cause the device to pinch your skin or even cut you.
You can find YouTube videos online that demonstrate how to perform this task. First, remove the head assembly from the housing before removing the shaver head from the blade assembly.
Find a flat surface to place it on. Next, you can remove the screens with the blade unit to clean. You can use the small brush that came with your shaver or even a small paintbrush will do the trick. The lubrication reduces friction caused between the metals inside. It also makes the blades feel smoother on your face. In order to keep your electric shaver working properly, you need to maintain it properly. Proper maintenance can save you hundreds of dollars in replacement shavers.
Remember, if something does go wrong, you can troubleshoot your way through the problem with the aforementioned guidance.If your Philips Shaver is not working or turning on, read below the possible causes and our advice on how to solve them yourself.
If you have a rechargeable Philips Shaver, it is possible, that its battery has drained out. We advise you to charge your shaver and then try turning it on again. For details on how to charge your shaver, please refer to the user manual. If your Philips Shaver is not rechargeable then it should be plugged in to a working electric socket while in use.
It is possible that your shaver does not turn on or move because it is dirty. There can be hair or dirt particles stuck inside it, causing the shaving heads to be blocked.
To fix this problem, properly clean your shaver. If possible, remove the shaving head and clean your shaver from the inside as well. For detailed cleaning instructions, refer to your user manual. In some shavers, a cleaning reminder symbol will blink to let you know that the shaver needs to be cleaned. Another reason why your shaver might not be working is that it is not assembled correctly.
How to Fix Braun Shavers
To find out proper instructions on how to reassemble your shaver, refer to your user manual. Some Philips Shavers have a 'travel lock' function.
If this is activated, the shaver does not turn on. Depending on the shaver model you have, you may see a 'lock' symbol blinking on your shaver to let you know that the travel lock is activated. Now try turning the shaver on again. It is possible that your Philips Shaver is damaged to such an extent that the motor cannot run anymore. In this case, please contact us to see how we can further help.
My Electric Shaver Doesn’t Shave — How To Fix It
Find your product. Not what you are looking for? Did we answer your question? If not, contact us. Chat now Chat offline. Payment We accept the following payment methods:. Quick links. Frequently asked questions.Many shavers manufactured by the Braun Company include an automatic cleaner that will clean, lubricate and recharge the shaver on a daily basis.
While the automatic cleaner should work well if properly charged and maintained, you may need a few other troubleshooting steps if the cleaner won't start. Connect the cleaning unit to a working power supply outlet; the power cord must be connected securely to the base of the cleaning unit. The power button should be "On" or the cleaner will not work.
Push the lift button on the front of the cleaner to open the cleaning compartment. Pull out the cleaning cartridge to check that you removed the lid from the cartridge. The cleaner will not start if the lid is still on. Look inside the cleaning compartment to check that there is adequate fluid in the cleaning cartridge.
Replace fluid if low or empty. Set the cleaning cartridge back into the cleaning unit and close the compartment. Press the "Start Cleaning" button on the front of the cleaning unit, as the cleaning unit will not start unless prompted by pressing the start button.
Meredith Jameson writes early childhood parenting and family health articles for various online publications. Hunker may earn compensation through affiliate links in this story. Step 1 Connect the cleaning unit to a working power supply outlet; the power cord must be connected securely to the base of the cleaning unit.
Step 2 Push the lift button on the front of the cleaner to open the cleaning compartment. Step 3 Look inside the cleaning compartment to check that there is adequate fluid in the cleaning cartridge. Step 4 Set the cleaning cartridge back into the cleaning unit and close the compartment.
Step 5 Contact an authorized Braun service center if the previous steps do not resolve the problem. Share this article. Meredith Jameson. Show Comments.And I say unfair because in the vast majority of these cases, the culprit for the sub-par performance of the shaver can be objectively pinpointed and addressed.
The typical scenario involves a recently bought electric shaver that fails to perform as expected: hairs left behind, not shaving close enough, razor burn and so on. There are a plethora of electric shavers out there: different types, different manufacturers and different price categories. And some of them simply perform poorly. For example, I mostly had bad experiences with Remington shavers and in a recent review I came across the worst performing Panasonic I have ever used. And Panasonic is probably my personal favorite manufacturer, but this only goes to show that one should always evaluate specific models or at least a series and not the manufacturer as a whole.
There are simply better shavers out there for the same money. You can check out our reviews section to get you started. Electric shaving is completely different from traditional shaving, be it with a cartridge, safety or straight razor. Assuming your shaver is suitable for the job, some prep work and a few technique adjustments can really transform your shaving experience. All electric shavers, even high-end models, perform best when your facial hair has a reasonable, manageable length.
Also, entry-level electric shavers are best suited for shaving dailywhen the stubble is short, while the more advanced ones can handle longer hairs decently. Attempting to go over those areas multiple times while applying more pressure will likely result in discomfort and more frustration. A solution would be to shave more often or to use a regular trimmer beforehand and reduce the length of your beard. Also, some electric shavers are better than others at shaving longer, flat-lying hairs.
You can read more about them here.Possible Fix, For A Wahl Senior Hair Clipper Power Cutting Out
For example, there are foil shavers that are better suited for coarsethick beards than others. Some work better for sensitive skin. Others can handle longer, wiry hairs better. A good place to start in picking the right shaver is our in-depth electric shaver buying guide and our recommended shavers chart. Hair clippings, dirt, dead skin or lather buildups can seriously impact the performance of a shaver.
Depending on how you use your shaver wet or dryyou may need to thoroughly clean your shaver more often. Most modern electric shavers can be safely cleaned with liquid soap and warm tap water. You will also need to lubricate your shaver on a regular basis. If you notice a significant drop in performance and shaver has a tendency to pull on the hairs, you should definitely buy new ones.
However, a radical stance resulting from a bad experience will certainly not help you in finding the cause of the problem and addressing it.One reason for this is of course the prevalence of Braun electric shavers, but the stations themselves are useful and practical as well.
The manufacturer even mentions this explicitly in the troubleshooting section of the user manual, but the directions are extremely vague and not particularly helpful.
So, in this guide, I will go over how to identify a clogged Braun cleaning station and how to unclog it in a few easy steps with detailed images. While they may seem complicated at first, the stations are actually pretty basic in the way they are constructed and in the way they work.
Basically, the cleaning fluid is pumped from the cartridge through a tube, it passes through the shaving head, then flows back into the cartridge through a small drain hole. The bottom of the cleaning chamber is actually slanted towards the drain hole so that the fluid would naturally flow back into the cartridge by gravity alone.
Regardless of your Braun station model, there are two holes on the inside of the station: one towards the top of the sloped inner chamber and one on the bottom corner.
With the station open, just push any debris and gunk with the toothpick until it falls from the drainage. You should also inspect the inner chamber and clean it of any hardened dirt, making sure not to push any of it into the drain.
When held at the right angle, you should be able to see daylight shining through a clean drain hole. If needed, you can turn the station upside down and clean any remaining dirt from the opposite side of the drain tube — this may be a bit difficult to perform without removing the top part of the station see step 4 below. Optionally, you can use a bit of warm tap water and just let it pass through the drain and wash any remaining debris.
Make sure however to do it carefully and slowly, with the water flowing directly into the inner cleaning chamber — the station itself is NOT waterproof and cannot be cleaned with water.
With your fingernail, gently push each tab inward. You should hear a click when a tab is unlocked. Once the outer shell is removed, locate the tube corresponding to the drain hole you just cleaned at step 3 and using the same toothpick or a q tip remove any remaining dirt from the vent. Assemble the station back in the same order, making sure to lock the four tabs by pressing them outward until they snap into place with a click.
The process is exactly the same for a Series 5, 7 or 9 station. The pump has this small propeller that rotates and pumps the fluid from the cartridge into the cleaning chamber of the station.
As mentioned previously, the impeller is a small propeller that needs to turn freely in order for the pump to work. With a toothpick or a small screwdriver, gently give it a few turns and loosen any dirt buildups that got stuck in there. Important : make sure not to confuse the impeller with the outer cover that also kind of looks like one.
Depending on a few factors, you may never have to deal with a blocked drain hole on your Braun station. Simply remove the cassette and gently tap the plastic frame on the edge of your sink to remove the hairs. You can then blow over it or use the small brush but only on the inside of the cassette, not directly over the foils to clear any remaining hair strands.
This only takes a few seconds, but it does make a difference and will also allow you to get more cleaning cycles out of a cartridge. Hardened lather can lead to a clogged drain probably more than anything and it can also cause pressure buildup inside the cartridge. The shaver must be dry before cleaning it in the station, so shake off the water and gently pat it dry with a towel.